بحث بعنوان Static and Dynamic Analysis of Lathe Spindle using ANSYS

أخواني في الله
أحضرت لكم كتاب
بحث بعنوان
Static and Dynamic Analysis of Lathe Spindle using ANSYS
Ayush Anand , Himel Roy
1Vellore Institute of Technology, Tamil Nadu, India.
2 School of Mechanical Department

و المحتوى كما يلي :

Abstract
There are various parameters over which the performance of
the spindle depends. This paper deals with the different
parameters of the spindle to find the optimized model from the
existing one. Based on the FEM, the static and dynamic
analysis has been performed. In the static analysis it considers
parameters such as material of the spindle, bearing span, Morse
taper. The dynamic analysis has been performed corresponding
to the optimized static model and modal shapes are obtained.
With the help of Campbell diagram, critical velocity has been
found out. The harmonic response is performed to check the
design and with the required speed transient analysis is
performed. All the analysis is performed in ANSYS
Workbench 18’.
Keywords: spindle; bearing; FEM; static analysis; dynamic
analysis; Campbell diagram; harmonic response; transient analysis
CONCLUSION
The analysis of spindle is performed on ANSYS Workbench
18’. Spindle structure and bearing plays an important role in
failure of spindle bearing system. Here, we proposed the optimization of spindle considering different parameters. The
result of static and dynamic analysis are in safe range.
The spindle consists of two sets of angular contact bearings
with grease lubrication. The optimized material is Alloy 4140
steel with bearing span of 101mm, MT 6, and spindle nose taper
of 7.5 degree. The deflection of the system is 2.2899 m.
According to the modal analysis the frequencies are 3087.5 Hz,
3088.6 Hz, 7897.9 Hz, 7898.9 Hz, 8012.5Hz and 9080.4 Hz
and from the Campbell diagram the critical velocities and
frequency found are 185274 rpm, 185286 rpm and 2912.9 Hz,
3272.1 Hz respectively. Also from harmonic analysis the
critical frequencies are 2912.9 Hz and 3272.1 Hz. The transient
analysis is performed at 6000 rpm and the deformation is
2.2931 m.
The ANSYS work bench is used by the designers as tools,
which increases the product quality, reduces cost and consumes
less time in design and development.
#ANSYS , #أنسس,#أنسس,#أنسس,#أنسيس,

كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net
أتمنى أن تستفيدوا من محتوى الموضوع وأن ينال إعجابكم
رابط من موقع عالم الكتب لتنزيل بحث بعنوان Static and Dynamic Analysis of Lathe Spindle using ANSYS
رابط مباشر لتنزيل بحث بعنوان Static and Dynamic Analysis of Lathe Spindle using ANSYS

كيفية التسجيل فى منتدى هندسة الإنتاج والتصميم الميكانيكى

طريقة التنزيل من المنتدى خطوة بخطوة

الهارد الشامل والمتكامل لقسم ميكانيكا

******************************************************

بحث بعنوان Static and Dynamic Analysis of Lathe Spindle using ANSYS 761752

» بحث بعنوان Gearbox Dynamic Modelling
» بحث بعنوان Similitude and Scaling Laws - Static and Dynamic Behaviour Beams
» بحث بعنوان Dynamic Vibration Analysis of Gear Box Casing Using ANSYS Software
» كتاب The Finite Element Method - Linear Static and Dynamic Finite Element Analysis
» بحث بعنوان Grinding Your Own Lathe Tools